Husqvarna 130L Gas Trimmer Manual

The Husqvarna 130L is a lightweight, professional-grade gas-powered trimmer designed for residential and commercial use. It features a 28cc 2-stroke engine, a straight shaft, a Tap-n-Go™ cutting head, an adjustable handle, and an anti-vibration system. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Setup 3. First-Time Operation 4. Specifications 5. Controls and Functions 6. Fuel & Oil Mixing 7. Operating Instructions 8. Maintenance Schedule 9. Storage & Winterization 10. Safety & Warnings 11. Troubleshooting

Features at a Glance

Key components: 28cc 2-stroke engine, Straight shaft, Tap-n-Go™ cutting head, Adjustable handle, Anti-vibration system, Air purge system, Combined choke/stop control.

Feature	Description
Engine	28cc, 2-stroke, air-cooled
Shaft	Straight, steel drive shaft
Cutting Head	Tap-n-Go™ bump feed for easy line advance
Handle	Adjustable D-handle for user comfort
Anti-Vibration	Reduces operator fatigue
Air Purge System	Removes air from fuel system for easier starting
Choke/Stop Control	Combined lever for choke and stop functions
Spark Arrestor	Standard muffler with spark arrestor screen
Fuel Tank	0.95 pint (0.45 liter) capacity
Cutting Swath	17 inches

Assembly & Setup

Unpack and inspect all parts. Assemble on a clean, flat surface.

Attach the shaft: Connect the two shaft sections and tighten the coupling.
Install the handle: Slide onto shaft, adjust to comfortable position, and tighten screws.
Attach the cutting head: Align and secure the Tap-n-Go™ head to the drive shaft.
Install the guard: Attach the debris shield to the shaft near the cutting head.
Fill with fuel/oil mix: Use fresh 50:1 gasoline to 2-stroke oil mixture.

WARNING! Always wear protective gloves and eyewear during assembly. Ensure all fasteners are tight.

First-Time Operation

Before starting, read all safety instructions.

Fuel: Fill tank with correct 50:1 fuel/oil mix.
Starting: Place on ground, set choke, press primer bulb 5-6 times, pull starter cord.
Warm-up: Allow engine to run at idle for 30-60 seconds.
Adjust handle: Set to comfortable operating position.
Test cutting head: Tap on ground to advance trimmer line.

CAUTION! Never operate in enclosed areas. Keep bystanders at a safe distance.

Specifications

Engine Type: 28cc 2-stroke, air-cooled.
Power Output: 0.8 kW (1.1 hp).
Fuel Capacity: 0.95 pint (0.45 liter).
Fuel/Oil Ratio: 50:1 (gasoline to 2-stroke oil).
Cutting Swath: 17 inches.
Shaft Type: Straight steel drive shaft.
Cutting Head: Tap-n-Go™ bump feed.
Weight: 10.1 lbs (4.6 kg) without fuel.
Sound Power Level: 106 dB(A).
Vibration Levels: Handle: 4.2 m/s² (left), 5.8 m/s² (right).

Controls and Functions

Main Controls: Throttle trigger, Throttle trigger lockout, Choke/stop control, Primer bulb, Starter grip.

Handle Area: Throttle trigger with lockout safety, Adjustable D-handle with vibration dampeners.

Engine: Combined choke/stop control (positions: Run, Choke, Stop), Air purge system, Spark plug with boot. Cutting Head: Tap-n-Go™ bump feed mechanism, Cutting line spool, Debris shield.

Fuel & Oil Mixing

Use fresh unleaded gasoline (minimum 89 octane) and Husqvarna 2-stroke oil or equivalent.

Mix ratio: 50:1 (2.6 oz oil per 1 gallon gasoline).
Use clean, approved fuel container.
Mix thoroughly before refueling.
Never use straight gasoline or motor oil.

Tip: Use fuel stabilizer if storing for more than 30 days. Always refuel outdoors, away from ignition sources.

Operating Instructions

Supports trimming and edging operations.

Starting: Set choke, prime, pull starter cord firmly.
Trimming: Hold at slight angle, swing in arc from right to left.
Line advance: Tap cutting head on ground while engine is running.
Edging: Rotate handle 90° so cutting head is vertical.
Stopping: Release throttle, move choke/stop control to STOP.
Avoiding damage: Do not force into dense vegetation or against hard objects.
Clearing debris: Stop engine and disconnect spark plug before clearing jams.
Cool down: Allow engine to idle for 30 seconds before stopping.

WARNING! Always wear eye protection, hearing protection, long pants, and sturdy shoes. Never operate without debris shield.

Maintenance Schedule

Daily: Check for loose fasteners, Clean air filter, Inspect cutting head. Weekly: Clean cooling fins, Check spark plug condition. Monthly: Clean fuel filter, Check fuel lines. Seasonally: Replace spark plug, Clean carburetor, Grease drive shaft.

Storage & Winterization

For storage over 30 days: Drain fuel tank and carburetor, Run engine until it stops. Remove spark plug, add 1 tsp oil through spark plug hole, pull starter 2-3 times, reinstall plug. Clean entire unit, store in dry, covered location.

CAUTION! Never store with fuel in tank indoors. Fuel vapors are explosive.

Safety & Warnings

Read manual completely before use. Wear PPE: eye protection, hearing protection, gloves, long pants, sturdy shoes. Keep bystanders 50 feet away. Never operate near flammable materials. Avoid electrical wires. Use right-hand grip only (left hand on handle). Stop immediately if unusual vibration occurs. The trimmer can throw objects at high speed—always use debris shield.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Engine won't start	No fuel, old fuel, spark plug	Check fuel level, use fresh mix, check/replace spark plug.
Engine runs poorly	Dirty air filter, carburetor	Clean/replace air filter, clean carburetor.
Line won't advance	Empty spool, tangled line	Refill spool with correct line, clear tangles.
Excessive vibration	Loose parts, bent shaft	Tighten all fasteners, inspect shaft for damage.
Engine overheats	Dirty cooling fins, lean mix	Clean cooling fins, check fuel mix and carburetor settings.

Service: For repairs, contact authorized Husqvarna service center.

Support: 1-800-487-5962; www.husqvarna.com/us