The Husqvarna FS 5000 D is a professional-grade floor saw designed for heavy-duty concrete cutting. This parts manual provides detailed diagrams, part numbers, and ordering information for all major components including the engine, cutting system, frame, wheels, and controls. Use this guide for maintenance, repair, and ordering genuine Husqvarna replacement parts to ensure optimal performance and safety.
This manual is intended for qualified service technicians. Always follow safety protocols when servicing the FS 5000 D.
| Safety Symbol | Meaning |
|---|---|
| ⚠️ WARNING | Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. |
| ⚠️ CAUTION | Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or equipment damage. |
| ℹ️ NOTE | Indicates important information or tips for proper operation and maintenance. |
WARNING! Disconnect the spark plug before performing any maintenance or parts replacement. Ensure the saw is on a stable, level surface.
Complete breakdown of the engine assembly, including part numbers for the cylinder, piston, crankshaft, carburetor, air filter, and muffler.
CAUTION! Use only genuine Husqvarna engine parts to maintain emissions compliance and performance.
Parts related to the blade spindle, arbor, flange, blade guard, and depth adjustment mechanism.
| Component | Part Number | Description |
|---|---|---|
| Blade Spindle Assembly | 234-567-01 | Main shaft holding the cutting blade. |
| Arbor Flange (Inner/Outer) | 234-567-02 | Secures the blade to the spindle. |
| Blade Guard (Upper) | 234-567-03 | Safety guard covering the blade. |
| Depth Adjustment Gear | 234-567-04 | Manual gear for setting cut depth. |
| Spindle Bearing Kit | 234-567-05 | Sealed bearings for the spindle. |
Structural components including the main frame, handlebars, control levers, and protective covers.
Tip: Inspect the frame for cracks or damage regularly, especially after heavy impacts.
Parts for the wheel axles, tires, drive belts/chains, and transmission (if applicable).
| Component | Part Number | Notes |
|---|---|---|
| Wheel Assembly (Complete) | 456-789-01 | Includes tire, tube, and rim. |
| Drive Belt | 456-789-02 | Check for wear and tension. |
| Axle & Bearing Kit | 456-789-03 | For front and rear wheels. |
| Transmission Gear Set | 456-789-04 | For mechanical drive models. |
| Hydraulic Pump/Motor | 456-789-05 | For hydraulic drive models. |
Throttle controls, clutch levers, cables, and linkage components.
WARNING! Ensure all control cables are properly routed and free from kinks or excessive wear to prevent unexpected operation.
Components for the water supply system used for dust suppression and blade cooling.
CAUTION! Use clean water to prevent clogging the pump and nozzles. Drain the system before storage in freezing conditions.
Ignition coil, spark plug, wiring harness, switches, and battery (if electric start).
| Component | Part Number | Specification |
|---|---|---|
| Ignition Coil | 789-012-01 | Check for spark if engine fails to start. |
| Spark Plug (Standard) | 789-012-02 | Refer to engine manual for correct gap. |
| Main Wiring Harness | 789-012-03 | Inspect for damaged insulation. |
| On/Off Switch | 789-012-04 | Located on the handlebar. |
| Battery (Electric Start Models) | 789-012-05 | 12V XX Ah. |
Common bolts, nuts, washers, seals, and gaskets used throughout the saw.
NOTE: Always replace fasteners with the correct grade and size. Do not reuse damaged or stretched bolts.
How to identify your machine and order genuine Husqvarna parts.
| Step | Action | Details |
|---|---|---|
| 1 | Locate Model & Serial Number | Find the product identification plate on the frame. Example: FS 5000 D, Serial # XXXXXX. |
| 2 | Use Part Numbers | Reference the part numbers listed in this manual when ordering. |
| 3 | Contact Dealer or Support | Provide model, serial number, and part number to your authorized Husqvarna dealer. |
| 4 | Online Resources | Use the Husqvarna Parts Lookup tool on the official website with your model number. |
Support: For technical assistance or to find a dealer, visit www.husqvarna.com or contact Husqvarna Customer Support at 1-800-HUSKY-62.