Husqvarna Z 248F Parts Manual

The Husqvarna Z 248F is a zero-turn riding mower featuring a 24 HP Briggs & Stratton engine, 48-inch fabricated mower deck, Hydro-Gear EZT transmission, and ergonomic controls. This parts manual provides detailed diagrams, part numbers, and ordering information for maintenance and repair. Below are key sections for identification, engine parts, deck assembly, drive system, controls, and troubleshooting.

Product Identification

Locate the model and serial number plate on the frame near the right rear wheel. Record these numbers for part ordering.

Engine Assembly & Components

24 HP Briggs & Stratton Intek V-Twin engine with key components listed below.

1. Air Filter Assembly: Includes filter element, housing, and pre-cleaner.
2. Carburetor & Fuel Pump: Complete assembly with gaskets and linkages.
3. Ignition System: Spark plugs, ignition coils, and wiring harness.
4. Cooling System: Blower housing, cooling fins, and fan.
5. Exhaust System: Muffler, exhaust pipe, and mounting hardware.

WARNING! Disconnect spark plug wire before servicing engine to prevent accidental start-up.

Mower Deck Assembly

48-inch fabricated steel deck with three spindle assemblies.

1. Deck Shell: Main housing with reinforcement brackets.
2. Spindle Assemblies: Includes spindle housing, bearings, pulleys, and belts.
3. Blades: Mulching or high-lift blades (part numbers vary).
4. Deck Lift System: Lift arms, linkage, and height adjustment pins.
5. Belt Guards & Idlers: Safety guards and belt tensioning components.

CAUTION! Ensure deck is securely supported and blades are stopped before servicing.

Drive System & Transmission

• Transmission: Hydro-Gear EZT (two units).
• Drive Belts: Main drive belt and transmission drive belts.
• Axles & Hubs: Rear axle assemblies with wheel hubs and keys.
• Pulleys: Engine pulley, idler pulleys, and transmission pulleys.
• Hydraulic Lines: Oil cooler lines and fittings (if equipped).
• Wheels & Tires: Front 13x6.5-6, Rear 20x10-8.

Controls & Operator Station

Control panel includes steering levers, ignition switch, and safety interlocks.

Steering Levers: Left and right control levers with linkages and bushings.

Seat & Suspension: High-back seat with suspension system and mounting hardware. Ignition Switch: Key switch with wiring. Parking Brake: Lever assembly and cable. Safety Switches: Seat switch, brake switch, and PTO switch.

Electrical System

12-volt system with battery, starter, and charging components.

1. Battery: 12V, 280 CCA (Group U1).
2. Starter Motor: Electric starter with solenoid.
3. Alternator/Charging System: Stator and voltage regulator.
4. Wiring Harness: Main harness with connectors and fuses.
5. Lights: Headlight assembly (if equipped).

Tip: Disconnect battery negative cable before electrical work.

Fuel & Hydraulic System

Fuel tank capacity: 3.5 gallons. Hydraulic reservoir for transmissions.

1. Fuel Tank: Polyethylene tank with cap, sending unit, and lines.
2. Fuel Filter: In-line fuel filter.
3. Hydraulic Reservoir: Tank with filter and breather cap.
4. Hydraulic Oil: Specify type and capacity (check manual).
5. Hoses & Clamps: Fuel and hydraulic hoses with clamps.

WARNING! No smoking or open flames near fuel system. Use proper fluid disposal methods.

Fasteners & Hardware

Common hardware: bolts, nuts, washers, pins, and clips. Refer to diagrams for specific sizes and grades.

Maintenance Schedule

Regular maintenance parts list: oil filter, air filter, spark plugs, blades, belts, and hydraulic filter.

CAUTION! Use only genuine Husqvarna parts for optimal performance and warranty.

Safety Information

Read operator's manual before use. Wear appropriate PPE. Keep hands and feet away from moving parts. Ensure all guards are in place. Park on level ground, engage parking brake, and remove key before servicing.

Troubleshooting & Part Ordering

Ordering: Use model and serial number when ordering parts. Contact authorized Husqvarna dealer or visit www.husqvarna.com.

Support: 1-800-487-5952; www.husqvarna.com/us/support