owners manual for husqvarna yth24v48 mower

The Husqvarna YTH24V48 is a 24-horsepower, 48-inch cutting width riding lawn mower with a V-twin engine, hydrostatic transmission, electric PTO engagement, cruise control, and a comfortable high-back seat. It features a durable steel frame, a heavy-duty cutting deck with anti-scalp rollers, and a 3.5-gallon fuel tank. Below are key sections for safety, features, operation, maintenance, troubleshooting, and specifications.

1. Features at a Glance 2. Safety Information 3. Assembly & Setup 4. Controls and Operation 5. Specifications 6. Maintenance Schedule 7. Cutting Deck Adjustment 8. Engine Care 9. Storage & Winterization 10. Troubleshooting 11. Warranty Information

Features at a Glance

Key components: 24 HP Briggs & Stratton V-twin engine, 48-inch fabricated cutting deck, Hydrostatic transmission, Electric PTO clutch, Cruise control, High-back seat, Headlights, Cup holder.

Feature	Description
Engine	24 HP Briggs & Stratton V-twin, OHV, electric start
Cutting Width	48 inches
Transmission	Hydrostatic, foot-pedal controlled
Cutting Deck	Fabricated steel, 3-blade, anti-scalp rollers
PTO Engagement	Electric switch
Speed Control	Forward/Reverse pedals, cruise control lever
Seat	Adjustable high-back with armrests
Fuel Capacity	3.5 gallons
Turning Radius	18 inches
Headlights	Integrated for low-light operation

Safety Information

Read all instructions before operating. Always wear appropriate safety gear.

Clear mowing area of debris, toys, and obstacles.
Do not carry passengers.
Do not mow on slopes greater than 15 degrees.
Engage parking brake before dismounting.
Disengage PTO and blades before crossing driveways or gravel.

WARNING! Keep hands and feet away from moving parts. Never operate without the discharge chute or grass catcher in place. Engine and muffler become extremely hot; allow to cool before servicing.

Assembly & Setup

Unpack and inspect all parts. Assembly requires basic tools.

Install steering wheel: Align and tighten bolt.
Attach seat: Mount to frame with provided bolts.
Install battery: Connect red (+) then black (-) terminals.
Check tire pressure: Inflate to 14 PSI (front) and 10 PSI (rear).
Add engine oil: Use SAE 30 or 10W-30, fill to dipstick mark.
Add fuel: Use fresh unleaded gasoline (87 octane minimum).

CAUTION! Mower is heavy; use assistance during assembly. Ensure all bolts are tightened securely.

Controls and Operation

Familiarize yourself with all controls before starting.

Dashboard: Ignition key, PTO switch, Choke, Throttle, Light switch, Cruise control lever.

Foot Controls: Forward pedal (right), Reverse pedal (left), Brake pedal.

Starting Procedure:

Set parking brake.
Ensure PTO switch is OFF.
Move throttle to FAST position.
Turn ignition key to START; release when engine starts.
Allow engine to warm up for 30 seconds.

Mowing: Engage PTO to start blades. Adjust speed with foot pedals. Use cruise control on long, straight paths.

Specifications

Model: YTH24V48
Engine: 24 HP Briggs & Stratton V-twin, 724cc
Cutting Width: 48 inches
Cutting Height: 1.5 to 4.5 inches (13-position adjustment)
Transmission: Hydrostatic, infinite forward/reverse speeds
Fuel Type: Unleaded gasoline (87 octane or higher)
Fuel Capacity: 3.5 gallons
Oil Capacity: 2.0 quarts (with filter)
Weight: 580 lbs
Warranty: 3-year limited

Maintenance Schedule

Regular maintenance ensures optimal performance and longevity.

Interval	Task
Before each use	Check tire pressure, engine oil level, fuel level
Every 8 hours	Check cutting deck for debris, inspect blades
Every 50 hours	Change engine oil, check air filter, grease fittings
Every 100 hours	Replace spark plug, check drive belt tension
Every season	Sharpen/replace blades, check battery charge

Tip: Always refer to the engine manual for specific engine maintenance details.

Cutting Deck Adjustment

Proper deck leveling ensures an even cut.

Park on level surface, disengage PTO, set parking brake.
Lower deck to desired cutting height using deck lift lever.
Measure distance from blade tips to ground at all four corners.
Adjust deck leveling nuts (front and rear) until measurements are equal.
Check belt tension and alignment periodically.

WARNING! Disconnect spark plug wire before performing any deck maintenance or blade service.

Engine Care

Follow engine manufacturer's guidelines for best performance.

Oil Change: Use SAE 30 or 10W-30. Drain when warm. Replace filter every other change.
Air Filter: Clean foam pre-cleaner every 25 hours. Replace paper element every 100 hours.
Spark Plug: Gap at 0.030 inches. Replace annually.
Fuel System: Use fuel stabilizer if storing over 30 days. Drain carburetor for long-term storage.

Storage & Winterization

Prepare mower for off-season storage to prevent damage.

Clean entire mower, especially under the deck.
Change engine oil and filter.
Add fuel stabilizer to tank and run engine for 5 minutes.
Disconnect battery negative terminal; store battery in cool, dry place.
Store in a clean, dry location, preferably on blocks to relieve tire pressure.

CAUTION! Never store with fuel in tank without stabilizer. Gasoline can degrade and damage fuel system.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Engine won't start	Dead battery, empty fuel tank, clogged fuel filter	Charge/replace battery; add fuel; replace fuel filter.
Poor cutting performance	Dull blades, uneven deck, low engine speed	Sharpen/replace blades; level deck; set throttle to FAST.
Excessive vibration	Damaged/debris-clogged blade, loose pulley	Stop engine, inspect and tighten blade; clean deck.
Loss of power	Dirty air filter, old spark plug, clogged cooling fins	Clean/replace air filter; replace spark plug; clean engine fins.
Hydrostatic transmission slips	Low fluid, worn drive belt	Check fluid level; inspect and replace drive belt if worn.

Reset: For electrical issues, disconnect battery for 5 minutes then reconnect.

Warranty Information

Husqvarna YTH24V48 includes a 3-year limited warranty for residential use. Warranty covers defects in materials and workmanship. It does not cover normal wear, misuse, or lack of maintenance. Proof of purchase is required. For warranty service, contact an authorized Husqvarna dealer. For support, visit www.husqvarna.com or contact 1-800-487-5962.